The earliest diamond saw blades used electroplating technology. In the middle and late 20th century, with the development of the world, people developed stone materials in the construction industry, and high-frequency welding technology appeared first. In , with the advent of laser welding technology, the process and function of diamond circular saw blades were also fully developed. Compared with the early high-frequency welding process, what are the advantages of the laser welding process? This is the focus of this discussion.

1: Heat resistance.

High-frequency welding technology has been controversial since its inception. Simply put, the choice of solder has always been an issue affecting the development of high frequency welding. Although there are many types of solders on the market at present, most of the solders have a melting point between 600-850 degrees Celsius. When the temperature exceeds 700 degrees Celsius, diamond began to show obvious high temperature carbonization. In the welding process, the thermal stability of the diamond is directly affected. In other words, the diamond will easily fall off during the cutting process, which directly affects the cutting. But if the soldering temperature is kept low, the cost of solder, such as silver solder tabs, rises rapidly. With 18% silver content of the solder, the melting temperature of the solder piece should exceed 800 degrees Celsius; if 35% tin-silver solder piece is used, the temperature can be controlled at about 700 degrees Celsius, which has a low impact on diamond carbonization.

In general, during the welding process of diamond saw blades, if the temperature required by the solder is high, diamond carbonization will occur, resulting in unstable cutting of the saw blade. But if the solder has a lower soldering melting point, then the cost of the solder goes up.

The laser welding saw blade adopts the method of fusion of the diamond segment and the saw blade, so that the saw blade and the diamond segments are not combined with solder, which has little effect on the thermal stability of diamond segment. That is a major advantage of laser welding saw blades. The most obvious manifestation of this advantage is that laser-welded saw blades can be used for dry cutting.



2: Welding strength.

In the high frequency welding process, the connection between the saw blade base and the diamond segment is completely dependent on the intermediate welding layer. Since there is a relatively large gap between the two, and welding and the like also directly affect the welding strength. Then during the cutting process, the diamond segment will often fly out, fall, etc., which may lead to some safety accidents. Therefore, the welding strength is a very important point for people. It has been found that if higher solder strength solders are used, it is necessary to increase the soldering temperature, which is in conflict with the thermal resistance of the diamond segment. People have been trying to solve this problem for a long time, but there is currently no solution.

The laser saw blade uses a laser, and the welding point is irradiated by a laser beam to increase the temperature of the welding point to a state of deep welding. This temperature can make the base of the saw blade and part of the diamond segment directly into a gaseous state, and evaporation occurs. Finally, through the protection of inert gas, the welding area is rapidly cooled at room temperature, and a very small welding part is finally formed. Due to the fast and efficient welding method, the welding strength is very high.



3: The thermal stability effect of the solder layer.

In the high-frequency welding process, although the lower part of the diamond segment is welded, because the high-frequency welding cannot heat the individual welding layer, the thermal stability of the upper diamond segment is often affected, which will also have a certain impact on the structure of the upper diamond segments. Especially if the solder is not easy to melt, the higher soldering temperature will directly bring more uncertainty to the whole diamond segment.

The laser welding process only heats the welding part and has no effect on other welding layers, so the benefit is to provide a more stable saw blade.

Of course, there are also some problems with laser welding saw blades. For example, the base of the saw blade cannot be reused, because the saw teeth are damaged during the first welding. This also leads to the high price of laser welding machines, so they are not widely used.

If you want to learn more, please visit our website.

Laser Welding Explained | Advantages and Disadvantages

Many of the amazing creations made possible by technology appear as if you took them directly from a movie. For instance, laser welding is feasible and presently in use, while laser cutting has been around for a while. For many welders, this "high-tech" style of welding is new or unfamiliar. This article discusses the advantages and disadvantages of laser welding technology.

What Is Laser Welding?

A laser beam creates a weld to fuse metals or thermoplastics during laser welding. Laser welding can generate narrow, deep welds between square-edged pieces in thicker materials and fast welding speeds of meters per minute in thin materials due to the concentrated heat source.

Conduction limited welding and keyhole welding are fundamentally different ways laser welding works. The interaction between the laser beam and the welded material depends on the laser's power density when it hits the workpiece.

• Conduction Limited Welding – Conduction-limited welding occurs when the power density is less than 105W/cm2. The laser beam does not penetrate the material; it is absorbed into its surface. Because of this, conduction-constrained welds frequently have a large width-to-depth ratio.
• Keyhole Welding – Laser welding is more frequently carried out by adopting a keyhole mechanism and larger power densities. The material in the path of the laser beam melts and vaporizes when the laser beam is focused on a small enough area to provide a power density typically> 106-107 W/cm2 before substantial amounts of heat can be dissipated by conduction. The concentrated laser beam enters the workpiece and creates a "keyhole" cavity filled with metal vapor (which, in some cases, can even be ionized, forming a plasma).

The Process Of Laser Welding

A strong laser beam is used in laser welding to heat the joint. When the material resolidifies, the components are fused because it has melted on both sides of the junction. The bare minimum requirements are a laser, lenses to focus where you want, a mechanism to precisely move the beam over the joint, and a worktable to fit up and hold the components.

Using optics to "organize" or "refine" light waves into a focused, highly intense beam is rather difficult. Therefore, a laser's workings are outside this page's purview. There are numerous types of lasers with various powers. But the proper beam can rapidly raise the temperature of the metal on both sides of a joint.

XMF contains other products and information you need, so please check it out.

The laser quickly applies the needed energy. You might need to fire the beam at the metal in pulses that last only a few milliseconds, depending on your laser and the nature of your workpieces. Or perhaps a continuous beam is ideal. You have a decent degree of flexibility over how the LBW system transfers heat to the pieces, but it depends on how much power is required.

Naturally, the molten metal will take a few seconds to cool and resolve. However, overall, the welding process is quick, making it a very efficient means of combining parts. Because of this, LBW is popular in applications requiring high welding speeds, such as manufacturing lines.

What Is The Purpose Of Laser Welding?

Many locations that use laser welding strongly emphasize creating neat, attractive welds. These consist of the following.

• Automobile production.
• Making jewelry.
• Fluid and hydraulic control components.
• Narrow shell assemblies that are distorted.
• Foils.
• Fuel rails.
• Medical equipment
• Heat exchangers are made of stainless steel.
• Thin-gauge metal tubes, components, and boxes

Benefits of Laser Welding

When compared to other welding methods, laser welding provides the following benefits:

• It enables quick welding, deep welding, and small deformation.
• The welding apparatus is straightforward and can be used to weld at ambient temperature or under various circumstances. For instance, a laser beam does not change as it passes through an electromagnetic field. Also, laser welding can be done in the air, vacuum, and with certain gases. Even materials like glass that are transparent to the beam can be welded through.
• It successfully joins dissimilar materials and can weld refractory materials like titanium and quartz.
• In high-power systems, a depth-to-width ratio of up to 5:1 and even up to 10:1 is possible due to the high power density made possible by laser beam focusing.
• Laser welding may perform micro-welding by obtaining a tiny, precisely positioned spot. It is suitable for joining tiny and micron-sized components made in bulk. (The smallest spot allowed is 0.1mm)
• Laser welding is flexible since it can reach hard-to-reach areas and uses non-contact long-distance welding. Laser welding has become increasingly popular and practical for automatic integration due to the YAG laser processing industry's recent use of optical fiber transmission technology.
• The laser beam may quickly and easily achieve beam splitting according to time and location, allowing for multi-beam simultaneous and multi-station processing and creating the ideal environment for more precise welding.

Drawbacks of Laser Welding

However, there are certain drawbacks to laser welding as well:

If you want to learn more, please visit our website Laser Welded Saw Blade.

• The weldment demands very high assembly accuracy, and the beam position on the workpiece shouldn't deviate too much. This is so that welding faults can occur when the workpiece assembly or beam location is imperfect. This is because the spot size after laser focusing is tiny, and the weld is narrow.
• The laser and its associated technologies are expensive and require a sizable upfront investment.